RMweb Gold 81C Posted December 2, 2018 RMweb Gold Share Posted December 2, 2018 Well yes but..........might stick with Panniers for now after my last adventure with the products of Dicky Jittery Mechanisms .. A Bachmann 64xx I'm told is a nice runner a buddy of mine Mick sent his Hattons 14xx back and got one of them he said it was the best thing he had done he even bought the Bachy auto coach to go with it.. 2 Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted December 4, 2018 RMweb Gold Share Posted December 4, 2018 One 28xx would be better Oh dear, someone please explain. Well yes but..........might stick with Panniers for now after my last adventure with the products of Dicky Jittery Mechanisms .. What you need, perhaps, is some Perseverance, old chap. Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted December 4, 2018 RMweb Gold Share Posted December 4, 2018 A Bachmann 64xx I'm told is a nice runner Not guaranteed, I fear, but I've managed to run my black one in nicely, so it's now ready to be converted to a 74XX. Now that's an idea, Rob, a nice 74XX for all kinds of general purpose, branch line work. 1 Link to post Share on other sites More sharing options...
RMweb Premium St Enodoc Posted December 4, 2018 RMweb Premium Share Posted December 4, 2018 Oh dear, someone please explain. Just remember your 14 times table CK. Link to post Share on other sites More sharing options...
RMweb Premium Northroader Posted December 4, 2018 RMweb Premium Share Posted December 4, 2018 NOOooo!!! (He’ll take his socks off) Link to post Share on other sites More sharing options...
RMweb Gold The Johnster Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 I had a Baccy 64xx and still have the mech, running under an ancient Mainline 57xx converted to 8750 with a K's cab from an even ancienter loco. It is a very smooth and controllable mech, but not quite up to the very high standard of the 57xx/8750 and 56xx, which IMHO are not too far off what it is reasonable to expect from a mass produced item! 1 Link to post Share on other sites More sharing options...
RMweb Gold NHY 581 Posted December 5, 2018 Author RMweb Gold Share Posted December 5, 2018 (edited) Oh dear, someone please explain. What you need, perhaps, is some Perseverance, old chap. Not guaranteed, I fear, but I've managed to run my black one in nicely, so it's now ready to be converted to a 74XX. Now that's an idea, Rob, a nice 74XX for all kinds of general purpose, branch line work. I can see the sense in that CK. A 74XX would fit in nicely. A 64xx plus auto trailer is on the cards as is a further 57xx or 8750. A 16xx would be even better but we will have to wait for the RTR job from model rail. The whole 14xx thing is still up in the air. I am not so inclined to spend on a model knowing that I am very likely to have to replace the chassis....... Rob Edited December 5, 2018 by NHY 581 1 Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 The whole 14xx thing is still up in the air. I am not so inclined to spend on a model knowing that I am very likely to have to replace the chassis....... I can see the sense in that, of course. I have now modified my expectations to make this easier. Each time I order a Hattons/DJM 14XX now, I do so in the full expectation that I will have to replace the chassis. Life thus has one less disappointment each time this is done. Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 (edited) You see, that looks a bit like the cab of a 74XX that young Cedrych Evans is looking out of. The vista has the whiff of the Aberystwyth to Carmarthen line about it, or possibly one of its branches? Edited December 5, 2018 by Captain Kernow 2 Link to post Share on other sites More sharing options...
RMweb Gold Stubby47 Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 That pagoda shed roof has collapsed quite badly. Link to post Share on other sites More sharing options...
woodenhead Posted December 5, 2018 Share Posted December 5, 2018 I can see the sense in that, of course. I have now modified my expectations to make this easier. Each time I order a Hattons/DJM 14XX now, I do so in the full expectation that I will have to replace the chassis. Life thus has one less disappointment each time this is done. Expectation is the devil of enjoyment and satisfaction. Live life without expectation and every chance of disappointment is removed 1 Link to post Share on other sites More sharing options...
woodenhead Posted December 5, 2018 Share Posted December 5, 2018 That pagoda shed roof has collapsed quite badly. And by the looks of it, that loss of paintwork at a uniform height on the side suggests an outside loo Link to post Share on other sites More sharing options...
RMweb Gold Stubby47 Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 The whole 14xx thing is still up in the air. I am not so inclined to spend on a model knowing that I am very likely to have to replace the chassis....... Sorted. 2 Link to post Share on other sites More sharing options...
br2975 Posted December 5, 2018 Share Posted December 5, 2018 (edited) I have several Bachmann 16ton minerals in the factory weathered finish,................................ They are excellent products if you ignore the complete lack of interior detail, not an issue with loaded wagons, Simple answer John, knock up a pair of simple simple jig(s) from some waste brass "like what I did" one to scribe the (i) side drop door (ii) top flap and the other to (iii) scribe the top line of the end door. . To use, you put the jig inside against a side wall of the 16 tonner and butt the lower end against one end. . Then scribe the top flap door lines. . Move the jig along inside the wagon to butt against the other end, then use the lower end to scribe the top and one vertical drop side door line. . Flip the jig over and repeat, until all lines are scribed. Brian R Edited December 5, 2018 by br2975 1 Link to post Share on other sites More sharing options...
br2975 Posted December 5, 2018 Share Posted December 5, 2018 I can see the sense in that, of course. I have now modified my expectations to make this easier. Each time I order a Hattons/DJM 14XX now, I do so in the full expectation that I will have to replace the chassis. Life thus has one less disappointment each time this is done. As I model South Wales circa 1971 - the disappointment of a 'dodgy' Hattons 14xx was of no consequence. . Until the wonderful Bob Masterman came up with this gem ! . D7083 towing the preserved GWS 1466 through Cardiff General during a Didcot - Onllwyn move in preparation for filming "Young Winston" during the summer of 1971. . I missed this move, but later found 1466 and the Toad inside the Canton wheel lathe shed on 27th June, 1971, apparently on the way back to Didcot. . Owning a Hymek, and a Toad, I'm not tempted (in the slightest) to buy a 14xx as well ! . Brian R 9 Link to post Share on other sites More sharing options...
Dr Gerbil-Fritters Posted December 5, 2018 Share Posted December 5, 2018 in preparation for filming "Young Winston" during the summer of 1971. Ah, one of the less well-known Thomas the Tank Engine episodes... Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 As I model South Wales circa 1971 - the disappointment of a 'dodgy' Hattons 14xx was of no consequence. . Until the wonderful Bob Masterman came up with this gem ! . D7083 towing the preserved GWS 1466 through Cardiff General during a Didcot - Onllwyn move in preparation for filming "Young Winston" during the summer of 1971. . I missed this move, but later found 1466 and the Toad inside the Canton wheel lathe shed on 27th June, 1971, apparently on the way back to Didcot. . Owning a Hymek, and a Toad, I'm not tempted (in the slightest) to buy a 14xx as well ! . Brian R The 14XX being towed - now that's something that you can replicate with the Hattons/DJM one. 3 Link to post Share on other sites More sharing options...
RMweb Gold The Johnster Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 The shadows (Cliff is apparently not present) suggest early afternoon, which may help identify the Peak hauled cross country express in platform 2. This was during my time at Canton, and I remember 1466 and her toad at the shed; IIRC they were stored in the wheel lathe to keep them out of sight and discourage trespass rather than for work on the wheel profile. The loco had played the part of a South African loco attacked and derailed by the Boers on which Churchill was riding as a war correspondent. The area around Craig Y Nos quarry was given the role of The Veldt. It looked very unconvincing to me! Link to post Share on other sites More sharing options...
RMweb Gold The Johnster Posted December 5, 2018 RMweb Gold Share Posted December 5, 2018 (edited) Simple answer John, knock up a pair of simple simple jig(s) from some waste brass "like what I did" one to scribe the (i) side drop door (ii) top flap and the other to (iii) scribe the top line of the end door. . To use, you put the jig inside against a side wall of the 16 tonner and butt the lower end against one end. . Then scribe the top flap door lines. . Move the jig along inside the wagon to butt against the other end, then use the lower end to scribe the top and one vertical drop side door line. . Flip the jig over and repeat, until all lines are scribed. Brian R Brilliant idea, Brian; you're not just a pretty face! I had been thinking along similar lines but your sketch neatly coalesces it for me! All of my steel 16 tonners are Baccy, so this should be a standard fit for all except the slope sider, which is loaded and doesn't need interior detail (I have a loaded and an empty rake so that I can have them passing each other at Cwmdimbath every early afternoon when the last trip of the morning turn, U21, passes the first of the afternoon job, U23). Edited December 5, 2018 by The Johnster 1 Link to post Share on other sites More sharing options...
Porcy Mane Posted December 5, 2018 Share Posted December 5, 2018 The vista has the whiff of the Aberystwyth to Carmarthen line about it, or possibly one of its branches? Neuadd-ddu. 13 Nov 1963, The loco being 7439([87G]). I felt it in my water. (I actually got it of Flickr) 1 Link to post Share on other sites More sharing options...
RMweb Gold Captain Kernow Posted December 6, 2018 RMweb Gold Share Posted December 6, 2018 (edited) Sorted. 14xx_peckett.png I can only say that that image is wrong on so many levels. It puts me in mind of someone like Dwayne Johnson being forced to wear a ballet skirt. Edited December 6, 2018 by Captain Kernow 1 Link to post Share on other sites More sharing options...
RMweb Gold NHY 581 Posted December 6, 2018 Author RMweb Gold Share Posted December 6, 2018 Ah!!! Found it!! Ciliau Aeron Railway Station Aberaeron to Lampeter. 13 Link to post Share on other sites More sharing options...
RMweb Gold Stubby47 Posted December 7, 2018 RMweb Gold Share Posted December 7, 2018 Rob, will you be voting for the DJM/Hattons 14xx in the BMRA non-rolling stock category ? 1 Link to post Share on other sites More sharing options...
RMweb Gold NHY 581 Posted December 7, 2018 Author RMweb Gold Share Posted December 7, 2018 Rob, will you be voting for the DJM/Hattons 14xx in the BMRA non-rolling stock category ? Yes. 1 Link to post Share on other sites More sharing options...
bgman Posted December 7, 2018 Share Posted December 7, 2018 Yes. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now