RMweb Gold Tony Wright Posted September 8 Author RMweb Gold Share Posted September 8 5 minutes ago, gingerangles said: Thanks for the reply @Tony Wright, looks like I definitely have the basis of an O4/1 then. The inclusion of the vacuum ejector pipe excluding the O4/3s. The tender doesn't seem to have any additional equipment as far as I can tell for a scoop... Is this tender rear correct for an O4/1? In LNER days, I assume most O4/1s still retained water pick-up gear. Bachmann's model was certainly an O4/1. I renumbered/detailed/weathered the one I had (note the 'ship's wheel' on the tender front to work the water pick-up). But the tender rear suggests no water pick-up gear (63635 was an O4/1). This O4/1 was built from a Little Engines kit, and it retains its pick-up gear. I must admit to being ignorant of many aspects of locos' tenders. It's probably true that the pick-up gear was removed from some O4s' tenders, but I leave it to those with the requisite knowledge to explain. Regards, Tony. 10 Link to post Share on other sites More sharing options...
RMweb Gold lezz01 Posted September 8 RMweb Gold Share Posted September 8 54 minutes ago, ScRSG said: Links, please. https://www.ebay.co.uk/str/beestudio2016 Motor house seems to have gone or should I say has nothing for sale as they are still registered as a vendor but there is this as well, I have brought from here. https://www.ebay.co.uk/str/helloalian?_trksid=p4429486.m3561.l170197 Regards Lez. 1 Link to post Share on other sites More sharing options...
RMweb Gold Barry Ten Posted September 8 RMweb Gold Share Posted September 8 (edited) 11 hours ago, Tony Wright said: They're 'Just Like The Real Thing' products in O Gauge. Whether they're still available, I don't know. Regards, Tony. I have a complete JLTRT pannier kit with wheels and motor/gearbox that I bought more than 15 years ago, but which I've never felt man enough to start building. Maybe this (or next) year will be the one. Edited September 8 by Barry Ten 1 3 Link to post Share on other sites More sharing options...
RMweb Gold Tony Teague Posted September 8 RMweb Gold Share Posted September 8 Tony I'd like to pose a question if I may. A little while ago I seem to recall that you posted a picture, of I know not what, which showed your 'rolling road' in the background. I did look back through the WW thread but despite going back 60 pages I couldn't find it, such is the pace at which this thread moves! I have a very poor DCC Concepts attempt at a rolling road, but each roller is loose rather than being fixable in position: This means that if you just touch one of the rollers with a loco wheel, or worse still a dangling bogie - and there is nothing worse than a dangling bogie! - then the roller just falls over, or off of the supporting track, which means it is very hard to get set up or to use. At the same time I seem to recall that the more superior device that you use is no longer in production? Can you tell me where it is from and / or whether there are any equivalents currently available? Tony 1 1 2 Link to post Share on other sites More sharing options...
RMweb Premium polybear Posted September 8 RMweb Premium Share Posted September 8 3 minutes ago, Tony Teague said: Tony I'd like to pose a question if I may. A little while ago I seem to recall that you posted a picture, of I know not what, which showed your 'rolling road' in the background. I did look back through the WW thread but despite going back 60 pages I couldn't find it, such is the pace at which this thread moves! I have a very poor DCC Concepts attempt at a rolling road, but each roller is loose rather than being fixable in position: This means that if you just touch one of the rollers with a loco wheel, or worse still a dangling bogie - and there is nothing worse than a dangling bogie! - then the roller just falls over, or off of the supporting track, which means it is very hard to get set up or to use. At the same time I seem to recall that the more superior device that you use is no longer in production? Can you tell me where it is from and / or whether there are any equivalents currently available? Tony That sounds very much like it could be the one previously manufactured by Bachrus in the USA - which I do believe is NLA. I have one - and very nice they are too. 2 1 Link to post Share on other sites More sharing options...
RMweb Premium St Enodoc Posted September 8 RMweb Premium Share Posted September 8 9 minutes ago, Tony Teague said: Tony I'd like to pose a question if I may. A little while ago I seem to recall that you posted a picture, of I know not what, which showed your 'rolling road' in the background. I did look back through the WW thread but despite going back 60 pages I couldn't find it, such is the pace at which this thread moves! I have a very poor DCC Concepts attempt at a rolling road, but each roller is loose rather than being fixable in position: This means that if you just touch one of the rollers with a loco wheel, or worse still a dangling bogie - and there is nothing worse than a dangling bogie! - then the roller just falls over, or off of the supporting track, which means it is very hard to get set up or to use. At the same time I seem to recall that the more superior device that you use is no longer in production? Can you tell me where it is from and / or whether there are any equivalents currently available? Tony Interesting - I've never had any trouble with my DCC Concepts rollers (usual disclaimer). 9 Link to post Share on other sites More sharing options...
RMweb Gold Tony Teague Posted September 8 RMweb Gold Share Posted September 8 17 minutes ago, St Enodoc said: Interesting - I've never had any trouble with my DCC Concepts rollers (usual disclaimer). Perhaps I'm just clumsy? Unless the rollers are exactly placed they can also move out of position whilst a loco is running on them - which either causes a loss of traction or in extreme cases, the loco falls off! 1 1 3 Link to post Share on other sites More sharing options...
RMweb Gold lezz01 Posted September 8 RMweb Gold Share Posted September 8 (edited) I too use the DCC Concepts rolling road and while some of them are a little loose most of them are fine. I must add that I use the EM/P4 spacers. Try adding a sliver of 5 thou plasticard or even paper to the outside edge of the bottom of the spacers to wedge them between the rails and that should sort out the problem. Just make sure that the metal is still in contact with the rails properly. 20231207_174439.mp4 Regards Lez. Edited September 8 by lezz01 6 1 2 1 Link to post Share on other sites More sharing options...
45568 Posted September 9 Share Posted September 9 Carrying on with the Midland 3F theme, let us not forget the 'oddball', 43435, which carried a Deeley/Fowler pattern tender unlike all its fellows! A Derby stalwart. A Bachmann 3F which is married to a modified Hornby 4F tender. The Bachmann 4F tender would be a quicker and better conversion but I did not have spare Bachy tender to hand. Cheers from Oz, Peter C. 12 1 1 Link to post Share on other sites More sharing options...
Popular Post 45568 Posted September 9 Popular Post Share Posted September 9 Also just finished, this Bachmann Fairburn 2.6.4 tank, revived from a rather shabby secondhand example to a Nottingham regular. Fox transfers numbers/crests, Modelmaster shed code. Detailing pack still available from Bachmann spares department. Cheers from Oz, Peter C. 19 3 1 Link to post Share on other sites More sharing options...
richard i Posted September 9 Share Posted September 9 8 hours ago, gingerangles said: Ah I see, thanks @richard i Will it be the right dimensions in other regards? I understand the '3's had 3500gal tenders originally. Depends on your loco of choice but for most it will be. 1 Link to post Share on other sites More sharing options...
RMweb Gold Tony Wright Posted September 9 Author RMweb Gold Share Posted September 9 (edited) 8 hours ago, Tony Teague said: Tony I'd like to pose a question if I may. A little while ago I seem to recall that you posted a picture, of I know not what, which showed your 'rolling road' in the background. I did look back through the WW thread but despite going back 60 pages I couldn't find it, such is the pace at which this thread moves! I have a very poor DCC Concepts attempt at a rolling road, but each roller is loose rather than being fixable in position: This means that if you just touch one of the rollers with a loco wheel, or worse still a dangling bogie - and there is nothing worse than a dangling bogie! - then the roller just falls over, or off of the supporting track, which means it is very hard to get set up or to use. At the same time I seem to recall that the more superior device that you use is no longer in production? Can you tell me where it is from and / or whether there are any equivalents currently available? Tony Good morning Tony, The rolling road I use is called 'The Saddle'. It's made (or was) by Bachrus (though I don't know if it's still available). Here it is in use underneath a DJH 'Princess Coronation' I was building.................... The beauty of it is, it's fully-adjustable (locked by a small allen key). Which means, not only can it be adjusted from N Gauge up to O Gauge (even though separate ones are/were sold as small, medium or large - this one is Med 50B-3), it can be set so that the rollers are a friction-fit between the rails, and can't be knocked out of position. Details on the box are 'The Saddle' by Bachrus (inc), sales@bachrus.com, www.bachrus.com, Tel: 905-337-9592, Fax: 905-337-0181 I hope this helps. Regards, Tony. Edited September 9 by Tony Wright clumsy grammar 6 1 3 Link to post Share on other sites More sharing options...
RMweb Gold Tony Wright Posted September 9 Author RMweb Gold Share Posted September 9 8 hours ago, St Enodoc said: Interesting - I've never had any trouble with my DCC Concepts rollers (usual disclaimer). I tried one, but it's not a patch on the Bachrus one. It was loose and wobbly in comparison. Regards, Tony. 1 2 2 Link to post Share on other sites More sharing options...
RMweb Gold Tony Wright Posted September 9 Author RMweb Gold Share Posted September 9 1 hour ago, 45568 said: Also just finished, this Bachmann Fairburn 2.6.4 tank, revived from a rather shabby secondhand example to a Nottingham regular. Fox transfers numbers/crests, Modelmaster shed code. Detailing pack still available from Bachmann spares department. Cheers from Oz, Peter C. Good morning Peter, Does the Bachmann detailing pack include the front steps? They're certainly not present on the loco as supplied. I fitted Comet ones to the detailed/modified/renumbered/weathered Bachmann Fairburn tank which runs on the little bit of LB (weathering by Geoff Haynes). The steps are slightly angled-out to accommodate the tighter curves on the M&GNR bit. I can't recall who brought this one (many years ago), but it was some Southern chaps (no front steps). I've had a couple of DJH Fairburn tanks pass through my hands for sale, including................. This one from the late Brian Lee's collection. And this one from the Peter Lawson collection. I can't recall where this DJH example came from, but it was professionally-painted. I built a DJH Fairburn 2-6-4T, it becoming the property of WMRC. I can't remember what happened to it. I have another to build, but when? Regards, Tony. 19 Link to post Share on other sites More sharing options...
RMweb Gold Tony Teague Posted September 9 RMweb Gold Share Posted September 9 1 hour ago, Tony Wright said: Details on the box are 'The Saddle' by Bachrus (inc), sales@bachrus.com, www.bachrus.com, Tel: 905-337-9592, Fax: 905-337-0181 Hi Tony Thanks for yoyr help on this; it looks like they have stopped trading as their web domain name is for sale, so I will have to look around for an alternative. Tony 1 2 Link to post Share on other sites More sharing options...
RMweb Premium John Isherwood Posted September 9 RMweb Premium Share Posted September 9 2 hours ago, Tony Wright said: Good morning Tony, The rolling road I use is called 'The Saddle'. It's made (or was) by Bachrus (though I don't know if it's still available). Here it is in use underneath a DJH 'Princess Coronation' I was building.................... The beauty of it is, it's fully-adjustable (locked by a small allen key). Which means, not only can it be adjusted from N Gauge up to O Gauge (even though separate ones are/were sold as small, medium or large - this one is Med 50B-3), it can be set so that the rollers are a friction-fit between the rails, and can't be knocked out of position. Details on the box are 'The Saddle' by Bachrus (inc), sales@bachrus.com, www.bachrus.com, Tel: 905-337-9592, Fax: 905-337-0181 I hope this helps. Regards, Tony. Tony, I couldn't agree more - I bought the one with four sets of rollers some years ago. As you say - fully adjustable, extremely well built, and very stable. If they are no longer available, then it's a great loss to the hobby. John Isherwood. 1 1 1 Link to post Share on other sites More sharing options...
Popular Post Barclay Posted September 9 Popular Post Share Posted September 9 Might as well add my own pannier to the collection, an 8750 based on a Hornby body, my first loco from the early 70's, detailed with lots of extra parts, and fitted with a Comet chassis, which I can recommend, though for this loco you will have to move the front splasher to the correct location. Also my own attempt at a rolling road, just some brass sections from the K&S stand and some cheap roller bearings. Not sophisticated but it works! 23 Link to post Share on other sites More sharing options...
RMweb Gold john new Posted September 9 RMweb Gold Share Posted September 9 1 hour ago, Tony Teague said: Hi Tony Thanks for yoyr help on this; it looks like they have stopped trading as their web domain name is for sale, so I will have to look around for an alternative. Tony Rolling roads - I have the DCC concepts one which I am more than happy with. 1 1 Link to post Share on other sites More sharing options...
RMweb Premium John Isherwood Posted September 9 RMweb Premium Share Posted September 9 1 hour ago, Tony Teague said: Hi Tony Thanks for yoyr help on this; it looks like they have stopped trading as their web domain name is for sale, so I will have to look around for an alternative. Tony A quick search for 'Bachrus' on Ebay would be productive. John Isherwood. 1 Link to post Share on other sites More sharing options...
RMweb Gold Popular Post Captain Kernow Posted September 9 RMweb Gold Popular Post Share Posted September 9 On the 3F and 4F theme, here is my 3F - a London Road Models kit, modified to represent a Somerset & Dorset example (built and weathered by me). Usual High Level gearbox and Mashima motor combination: 21 4 1 Link to post Share on other sites More sharing options...
RMweb Gold MikeParkin65 Posted September 9 RMweb Gold Share Posted September 9 2 hours ago, Tony Wright said: Does the Bachmann detailing pack include the front steps? Unfortunately not - as you've found the Comet ones are the best aftermarket solution Link to post Share on other sites More sharing options...
RMweb Premium gingerangles Posted September 9 RMweb Premium Share Posted September 9 (edited) 1 hour ago, Barclay said: Might as well add my own pannier to the collection, an 8750 based on a Hornby body, my first loco from the early 70's, detailed with lots of extra parts, and fitted with a Comet chassis, which I can recommend, though for this loco you will have to move the front splasher to the correct location. Also my own attempt at a rolling road, just some brass sections from the K&S stand and some cheap roller bearings. Not sophisticated but it works! This is potentially an option with the DCC concepts items, they could be detached from their spaces and placed in jigs like this. You'd just lose the ability to drop them on a piece of track. I also have the DCC items and know exactly what the OP is talking about. Edited September 9 by gingerangles 2 Link to post Share on other sites More sharing options...
45568 Posted September 9 Share Posted September 9 2 hours ago, Tony Wright said: Good morning Peter, Does the Bachmann detailing pack include the front steps? Unfortunately not Tony! Overlooked by Bachmann for some reason. However, my large box of accumulated Hornby and other spares, mostly purchased from Peters Spares when they exported overseas at a reasonable cost, and spares were plentiful, provided suitable items from the Hornby Thompson L1 detailing pack! Cheers from Oz, Peter C. 1 Link to post Share on other sites More sharing options...
RMweb Premium polybear Posted September 9 RMweb Premium Share Posted September 9 1 hour ago, John Isherwood said: A quick search for 'Bachrus' on Ebay would be productive. John Isherwood. Beware that one of those coming up in the search is most definitely NOT Bachrus - only the plastic box is (being sold by Rails of Sheffield). 1 Link to post Share on other sites More sharing options...
RMweb Premium Popular Post Michael Edge Posted September 9 RMweb Premium Popular Post Share Posted September 9 If we've got to Fairburn 2-6-4Ts here's my scratchbuilt one from 1985 This runs on Herculaneum Dock, front steps and cylinders in the right place but no problem on 28" radius curves. 14 12 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now