Danemouth Posted October 26, 2010 Share Posted October 26, 2010 I am about to get a NCE Powercab starter set for my new layout Danemouth. This is my first time with DCC and I want to get it right at the beginning - don't we all There will be 10 Seep point motors to operate, so I am in the process of deciding which accessory decoder to use. I've search the forum and ended up slightly bemused so I though I would ask the question directly - I've been recommended to use the Team Digital SMD82. Does anybody have any experience with is decoder please - what do you think of it? Does anybody suggest an alternative that reliably works with the Powercab and Seeps? Thanks in advance, Dave Link to post Share on other sites More sharing options...
HLT 0109 Posted October 26, 2010 Share Posted October 26, 2010 Dave, I use Powercab but not Seep point motors. However, I believe Seeps are solenoid operated which is the same type as the Hornby point motors I use. Because I decided on Hornby originally, I use the Hornby R8247 Point and Accessory Decoders and can confirm that Powercab operates them perfectly. Hornby's decoder controls four points from each unit - I believe other makes may control more so one consideration may be how many units you need to control all your points. In case it is of interest, if you have two points you always want to control in unison, you can wire them to one port of the decoder. I hope this helps, Harold. Link to post Share on other sites More sharing options...
StaffsOatcake Posted October 26, 2010 Share Posted October 26, 2010 I use the powercab/Procab to operate a few Lenz LS 150 units that in turn operate SEEP motors. The Lenz units take only the command information from the Powercab and the LS150 units have their own power supply a lenz TR150 unit and have never had a problem at all. The Lenz LS150 units have six outputs so for 10 pints you will only need two Link to post Share on other sites More sharing options...
pitbull1845 Posted October 26, 2010 Share Posted October 26, 2010 Dave I have used the Lenz LS150 and have had no problems with it at all. Very simple to wire up and install. Cheers Scott Link to post Share on other sites More sharing options...
Edwin_m Posted October 26, 2010 Share Posted October 26, 2010 If you use LS150s you have to use a big power supply as these don't include a CDU. I use the MERG decoders. About £12 for four pairs of outputs each of which will happily throw two Seeps in parallel. Link to post Share on other sites More sharing options...
Pete the Elaner Posted October 26, 2010 Share Posted October 26, 2010 You won't regret choosing a Powercab either. It is very upgradeable & user-friendly. Link to post Share on other sites More sharing options...
RMweb Gold RedgateModels Posted October 27, 2010 RMweb Gold Share Posted October 27, 2010 Another vote for MERG accessory decoder boards from me If you don't fancy building your own then make sure that any proprietary unit has a CDU (Capacitive Discharge Unit) built in, you can get away without one as some have said earlier, but why take the risk. The Team Digital unit is very good, if a bit pricey Link to post Share on other sites More sharing options...
Danemouth Posted October 27, 2010 Author Share Posted October 27, 2010 Many thanks for all your most helpful advice, I will investigate both the Lenz and MERG options Dave Link to post Share on other sites More sharing options...
RMweb Premium melmerby Posted October 27, 2010 RMweb Premium Share Posted October 27, 2010 If you use LS150s you have to use a big power supply as these don't include a CDU. I use the MERG decoders. About £12 for four pairs of outputs each of which will happily throw two Seeps in parallel. The LS150 recommended supply is 3A max. That is fine for Seeps MERG OK if you are a kitbuilder! Another alternative is LDT - kit or ready made. Keith Link to post Share on other sites More sharing options...
Danemouth Posted October 28, 2010 Author Share Posted October 28, 2010 The LS150 recommended supply is 3A max. That is fine for Seeps MERG OK if you are a kitbuilder! Another alternative is LDT - kit or ready made. Keith Keith, Thanks for the info, will have a look at LDT. I liked the LS150 decoders but needing two of them with power supplies put me the wrong side of 160 notes - therefore forget it! As well as the kits mentioned I am also looking at the Digitrax DS64 - needs a 12 V DC supply though. At this rate I will end up with conventional point control, Thanks, Dave Link to post Share on other sites More sharing options...
RMweb Premium melmerby Posted October 28, 2010 RMweb Premium Share Posted October 28, 2010 Keith, Thanks for the info, will have a look at LDT. I liked the LS150 decoders but needing two of them with power supplies put me the wrong side of 160 notes - therefore forget it! As well as the kits mentioned I am also looking at the Digitrax DS64 - needs a 12 V DC supply though. At this rate I will end up with conventional point control, Thanks, Dave Hi Dave The LS150 is around £40 each so I wouldn't expect to pay another £80 for transformers (Lenz own ready cased are too expensive for me!) SEE: RAPIDonline part 88-3948 (2x 15v outputs) would do the job if you feel like doing it yourself. Buy a case from i.e Maplin and some suitable connectors and save yourself a wad! I've actually used some toroidal transformers (not Rapid) for my supplies - bit of a luxury as they are more expensive! Keith Link to post Share on other sites More sharing options...
RMweb Gold DaveyH Posted October 28, 2010 RMweb Gold Share Posted October 28, 2010 I use Lenz LS110 accessory decoders to run a mixture of Peco and Seep point motors with the Powercab. I use a seperate power supply that was rescued from a Kodak photo printer! The beauty of recycling Not yet had a problem, though finding the LS110s is becoming more difficult. Link to post Share on other sites More sharing options...
pendlerail Posted November 1, 2010 Share Posted November 1, 2010 I also use the Lenz LS150 on my layout with 10 points works ok for me not had any problems, Phil Link to post Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.