RMweb Premium DLT Posted May 9, 2017 Author RMweb Premium Share Posted May 9, 2017 ... one can end up spending too much time posting and not enough time modelling. Can't argue with that! Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted May 11, 2017 Author RMweb Premium Share Posted May 11, 2017 There is an operating rod running along the boiler, high up beside the domes (blower valve?) and the supports are right on the boiler-bands. Trying to work out the spacing of the boiler bands and boiler fittings is a bit of a challenge without a side-on photo, and the Russell drawing doesn't show the twin-dome boiler. The I had a bit of a "Doh" moment. Its the same (C3 type) boiler as fitted to the C2X class, and lo-and-behold, the Russell drawing of the C2X DOES show the twin-dome version. Why didn't I look at that before? Dave. Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted May 11, 2017 Author RMweb Premium Share Posted May 11, 2017 (edited) I had to share a photo of the loco with a somewhat bizarre colourful boiler. The markings in the red ink are the positions of boiler bands, the black ink the boiler fittings and the control rod. Domes etc are sat on blobs of Blue-Tack. Dave. Edited September 5, 2022 by DLT 9 Link to post Share on other sites More sharing options...
RMweb Premium Daddyman Posted May 11, 2017 RMweb Premium Share Posted May 11, 2017 I had to share a photo of the loco with a somewhat bizarre colourful boiler. The markings in the red ink are the positions of boiler bands, the black ink the boiler fittings and the control rod. Domes etc are sat on blobs of Blue-Tack. Dave. IMG_1237 small.jpg Looking good! Is that red mark behind the smokebox for the drainpipe? If so good to see you've decided to include it! I assume there's no need to tell you that paint will not take on top of felt pen? Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted May 15, 2017 Author RMweb Premium Share Posted May 15, 2017 (edited) Coming together slowly, most boiler fittings now done, detailing the cab at the mo. Cheers, Dave. Edited September 5, 2022 by DLT 17 1 Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted May 17, 2017 Author RMweb Premium Share Posted May 17, 2017 (edited) Awaiting another Gibson order now; for buffers, Westinghouse pipes, and a better set of trailing wheels. Old style Romfords came with the kit which don't run very well when going bunker first. They also need better bearings rather than just a couple of slack holes in the frame. There's also the below-footplate detail to come, the air brakes create a fair bit of pipework. And there must be an air reservoir somewhere, but I can't see it in the prototype photos. More updates when there's something to show. Dave. Edited May 17, 2017 by DLT Link to post Share on other sites More sharing options...
KalKat Posted May 18, 2017 Share Posted May 18, 2017 May I ask where the C2X boiler etch you used came from please? I would like a couple of these locos for my (eventual) railway, and not being overly impressed by DJH thought I might scratchbuild..................... Emma Link to post Share on other sites More sharing options...
number6 Posted May 18, 2017 Share Posted May 18, 2017 The boiler is from an ACE models kit for the C2X - I have raided it for various bits and bobs so there isn't much of it left now! It is possible you could roll your own for the bother of getting just this part? The domes Dave have are also from the kit. So it is possible you could get these as separate items from ACE. Can't say I have knowingly ever seen a completed one of these models - the DJH one is wrong in some places but certainly builds into a good looking loco. Link to post Share on other sites More sharing options...
RMweb Premium pete_mcfarlane Posted May 18, 2017 RMweb Premium Share Posted May 18, 2017 Can't say I have knowingly ever seen a completed one of these models - the DJH one is wrong in some places but certainly builds into a good looking loco. I built one of the DJH kits years ago. The main problems were the loco sitting 2mm too high on the chassis (easily fixed by filing the big cast lump under the footplate off) and the cab roof being too small (it lacked any overlap at the sides). I also replaced the frame spacers with Comet ones (as supplied it was way too narrow, even for OO) and used Gibson coupling rods. I was quite pleased with it. Link to post Share on other sites More sharing options...
number6 Posted May 18, 2017 Share Posted May 18, 2017 I remember your comments on the loco Pete. If it wasn't clear I meant one of the etched ACE kit versions. I get a bit defensive over them despite come criticisms as they do produce locos in 4mm that aren't available elsewhere - even if there are some 'reduced from 7mm' problems here and there! Link to post Share on other sites More sharing options...
RMweb Premium pete_mcfarlane Posted May 18, 2017 RMweb Premium Share Posted May 18, 2017 I remember your comments on the loco Pete. If it wasn't clear I meant one of the etched ACE kit versions. I get a bit defensive over them despite come criticisms as they do produce locos in 4mm that aren't available elsewhere - even if there are some 'reduced from 7mm' problems here and there! I've yet to try any of ACE's kits, but as you say, they do some interesting locos. I'd rather fancy a J1 or J2 one day, ditto a K. Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted May 18, 2017 Author RMweb Premium Share Posted May 18, 2017 Gibson order arrived today, and the first thing I did was fit the trailing wheels. It was test-run at high speed bunker first on some of the pretty ropey track on Charmouth without derailing on the facing points. Cheers, Dave. PS I had a look at the C2X on the DJH website; and apart from sitting a bit high it looks pretty good. Interestingly the list of SR loco kits has dwindled to three: http://www.djhmodelloco.co.uk/sr-kits/ Link to post Share on other sites More sharing options...
RMweb Premium 2ManySpams Posted May 18, 2017 RMweb Premium Share Posted May 18, 2017 Coming together slowly, most boiler fittings now done, detailing the cab at the mo. IMG_1240 small.jpg Cheers, Dave. You've done wonders with this semi-scratch build Dave. I do think though that there's room for at least one more dome on that boiler. Link to post Share on other sites More sharing options...
N15class Posted May 19, 2017 Share Posted May 19, 2017 Gibson order arrived today, and the first thing I did was fit the trailing wheels. It was test-run at high speed bunker first on some of the pretty ropey track on Charmouth without derailing on the facing points. Cheers, Dave. PS I had a look at the C2X on the DJH website; and apart from sitting a bit high it looks pretty good. Interestingly the list of SR loco kits has dwindled to three: http://www.djhmodelloco.co.uk/sr-kits/ Not surprising really I know the Moguls and S15's were not that good or accurate. Link to post Share on other sites More sharing options...
bigbadbadge Posted May 30, 2017 Share Posted May 30, 2017 Hi Dave I am sorry but I have been absent due to a loft conversion which is still ongoing although painting now. This looks absolutely stunning, thanks for the tip on making the washout plugs I may have to use that in future. Did you secure the drill to anything ? Keep up the great work All the bestChris Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted May 30, 2017 Author RMweb Premium Share Posted May 30, 2017 I used a lightweight cordless drill, holding it on the bench and holding the power on with one hand, the other hand held the needle file. Not a great method from any point of view, but it worked. I know I haven't posted for nearly a fortnight, but I am progressing. There's masses of detail bits to attend to; particularly all the pipework below the footplate, vacuum pipes, injectors, Westinghouse pipes etc, all of which is pretty visible. And I haven't got to one of the most ticklish jobs yet,fixing the lamp irons on the bunker rear. Photos when all done. Cheers, Dave. Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted May 31, 2017 Author RMweb Premium Share Posted May 31, 2017 (edited) At last some tangible progress to show, and enough to pose the loco on the layout rather than the workbench! Yet again, most of the bits and pieces of pipework etc are balanced in place, and won't be fixed until after painting. Some closeups to show details etc, all the under-footplate pipework is fixed in place. I think these photos show what a bruiser this loco is! This one shows how the handrails are curved around the clack-valves. The solid brackets holding the tanks on that we discussed earlier, are solid lumps of plasticard, fabricated and then filed to shape. Like much of it, they are just perched there for the photos. Still more bits to fit, tank handrails and lampirons on top, and sandboxes and pipes down below. Sandpipes may be awkward, as they will have to go on AFTER the brake-rigging. That's it for now, Cheers, Dave. Edited September 5, 2022 by DLT 13 Link to post Share on other sites More sharing options...
number6 Posted May 31, 2017 Share Posted May 31, 2017 "Resounding applause and cheers" Looks like I might have to beef up the legs on the layout a bit. Link to post Share on other sites More sharing options...
RAY NORWOOD Posted May 31, 2017 Share Posted May 31, 2017 At last some tangible progress to show, and enough to pose the loco on the layout rather than the workbench! Yet again, most of the bits and pieces of pipework etc are balanced in place, and won't be fixed until after painting. P1070221 small.jpg P1070222 small.jpg P1070220 small.jpg Some closeups to show details etc, all the under-footplate pipework is fixed in place. I think these photos show what a bruiser this loco is! P1070227 small.jpg P1070226 small.jpg This one shows how the handrails are curved around the clack-valves. P1070228 small.jpg The solid brackets holding the tanks on that we discussed earlier, are solid lumps of plasticard, fabricated and then filed to shape. Like much of it, they are just perched there for the photos. Still more bits to fit, tank handrails and lampirons on top, and sandboxes and pipes down below. Sandpipes may be awkward, as they will have to go on AFTER the brake-rigging. That's it for now, Cheers, Dave. Really looking good Dave Link to post Share on other sites More sharing options...
RMweb Premium Daddyman Posted May 31, 2017 RMweb Premium Share Posted May 31, 2017 Well done. That cab aperture looks superbly crisp, square and even. Link to post Share on other sites More sharing options...
Jack P Posted June 1, 2017 Share Posted June 1, 2017 Looks excellent as per usual Dave! Link to post Share on other sites More sharing options...
jrg1 Posted June 1, 2017 Share Posted June 1, 2017 A terrifically good rendition of a workaday engine-I would be hesitant to paint it; it looks great in the raw! Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted June 1, 2017 Author RMweb Premium Share Posted June 1, 2017 Thanks for all the comments guys Lampirons are now fitted, with the exception of the high ones on the front footplate. These will be a bit vulnerable to damage, so will be added after painting. Cheers, Dave. Link to post Share on other sites More sharing options...
RMweb Premium DLT Posted June 2, 2017 Author RMweb Premium Share Posted June 2, 2017 (edited) Took these photos to get a better look at the latest details, in particular the sandpipes and lampirons: Hmmmm, do the sandpipes look a little too hefty? Edited September 5, 2022 by DLT 6 1 Link to post Share on other sites More sharing options...
RMweb Premium Daddyman Posted June 3, 2017 RMweb Premium Share Posted June 3, 2017 They might be slightly. But the bigger problem for me is that all the lovely pipework draws the eye to the infandous Romfords. They're not worthy of you - the crispness and evenness of that bunker rear (and the rest of the build) is way beyond the standard of the wheels. And you're clearly skilled enough to use Gibsons... On second thoughts, I suppose you might have a plan for hiding the nut in the wheel centre? Can't remember what you've done on previous builds. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now