hucknall byron Posted March 21, 2020 Share Posted March 21, 2020 I have had fitted a Lais decoder into my Hornby 101 DMU. All was well and I put it away for a while during urgent engineering work on the layout. It now runs very badly, jerky and almost running backwards at times but not quite. Any suggestions? Link to post Share on other sites More sharing options...
WIMorrison Posted March 21, 2020 Share Posted March 21, 2020 Get a Zimo decoder 2 Link to post Share on other sites More sharing options...
cravensdmufan Posted March 21, 2020 Share Posted March 21, 2020 39 minutes ago, hucknall byron said: I have had fitted a Lais decoder into my Hornby 101 DMU. All was well and I put it away for a while during urgent engineering work on the layout. It now runs very badly, jerky and almost running backwards at times but not quite. Any suggestions? Try setting CV8 to 8. This should reset the decoder back to factory settings. The loco address will revert back to 3 so you will have change that back to your desired running number. I have had decoders lose memory over a period out of use. And not just cheap ones either. Factory reset usually gets them back to normal. 1 Link to post Share on other sites More sharing options...
RMweb Premium Michael Edge Posted March 21, 2020 RMweb Premium Share Posted March 21, 2020 Factory reset isn't 8 but I can't remember what it is. I've used a couple of these and had lots of problems with them. 1 Link to post Share on other sites More sharing options...
hucknall byron Posted March 21, 2020 Author Share Posted March 21, 2020 Well I have had a go with altering CV8 to 8 but my powercab wont even read the chip. I am assuming the chip is the problem and needs replacing? I hadn't much faith in it at the outset to be honest but I thought I would give it a go. Any suggestions for a replacement? the model is very basic no lights and all I want it to do is smoothly go backwards and forwards. It is 8 pin dcc ready. Link to post Share on other sites More sharing options...
johnb Posted March 21, 2020 Share Posted March 21, 2020 As above get a Zimo Link to post Share on other sites More sharing options...
OFFTHE RAILS Posted March 21, 2020 Share Posted March 21, 2020 31 minutes ago, hucknall byron said: Well I have had a go with altering CV8 to 8 but my powercab wont even read the chip. I am assuming the chip is the problem and needs replacing? I hadn't much faith in it at the outset to be honest but I thought I would give it a go. Any suggestions for a replacement? the model is very basic no lights and all I want it to do is smoothly go backwards and forwards. It is 8 pin dcc ready. The Laisdcc decoder is on their website - it has all the CV default values and ranges. To reset the decoder, set CV8 to 4 and/or CV30 to 4 Ian 1 Link to post Share on other sites More sharing options...
hucknall byron Posted March 21, 2020 Author Share Posted March 21, 2020 Zimo seems to be about double the price of a Lenz standard? Are they that much better running quality wise or is there something else? Not very good when it comes to this part of our hobby I'm afraid. Link to post Share on other sites More sharing options...
WIMorrison Posted March 21, 2020 Share Posted March 21, 2020 Really? A Zimo MX600r should be around £20 2 Link to post Share on other sites More sharing options...
hucknall byron Posted March 21, 2020 Author Share Posted March 21, 2020 Thanks Iain I will have another look round. Link to post Share on other sites More sharing options...
RMweb Gold RedgateModels Posted March 21, 2020 RMweb Gold Share Posted March 21, 2020 23 minutes ago, WIMorrison said: Really? A Zimo MX600r should be around £20 What he said 1 1 Link to post Share on other sites More sharing options...
hucknall byron Posted March 21, 2020 Author Share Posted March 21, 2020 Thanks Ian, I knew this would smoke you out. Link to post Share on other sites More sharing options...
cravensdmufan Posted March 21, 2020 Share Posted March 21, 2020 3 hours ago, hucknall byron said: Well I have had a go with altering CV8 to 8 but my powercab wont even read the chip. I am assuming the chip is the problem and needs replacing? I hadn't much faith in it at the outset to be honest but I thought I would give it a go. Any suggestions for a replacement? the model is very basic no lights and all I want it to do is smoothly go backwards and forwards. It is 8 pin dcc ready. Just before you give up on the decoder - try this with your Powercab: Put loco on Program Track Press PRO/ESC four times (USE PROGRAM TRK appears) Press ENTER Press 7 (RECOVERY PROGRAM?) Press 1 (=YES) it will page through the decoder and the loco should jiggle a bit on the track. When it's done it's thing press PROG/ESC. With luck the decoder will now be reset. (Loco address 3). Give that a go and let us know how you get on. Link to post Share on other sites More sharing options...
WIMorrison Posted March 21, 2020 Share Posted March 21, 2020 (edited) How is that any different from just setting CV8=8 or in the case of LAIS CV8=2? https://laisdcc.com/LaisDcc_Decoders_Manual.pdf Edited March 21, 2020 by WIMorrison Link to post Share on other sites More sharing options...
cravensdmufan Posted March 21, 2020 Share Posted March 21, 2020 (edited) 5 minutes ago, WIMorrison said: How is that any different from just setting CV8=8? Well it's somehow different - it worked with a few of mine when CV8 to 8 didn't. I don't know the ins and outs of it but it's worth him having a go. Edit: The NCE manual says (quote) "RECOVERY PROGRAMMING re-programs a decoder's CVs in an attempt to get an 'insane' decoder back to somewhat normal operation". Now that could of course be the same as the CV8 thing but I notice when I used that option 7 the loco jiggles on the track while it's paging through. Edited March 21, 2020 by cravensdmufan Additional wording Link to post Share on other sites More sharing options...
WIMorrison Posted March 22, 2020 Share Posted March 22, 2020 12 hours ago, Michael Edge said: Factory reset isn't 8 but I can't remember what it is. I've used a couple of these and had lots of problems with them. CV8=2 for Lais according to their manual Link to post Share on other sites More sharing options...
OFFTHE RAILS Posted March 22, 2020 Share Posted March 22, 2020 7 hours ago, WIMorrison said: CV8=2 for Lais according to their manual CONFUSING... On the LAISDCC website ( https://laisdcc.com/LaisDcc_Decoders_Manual_V2.pdf ) the V2 manual states: Visit our Page LaisDccTM Decoders Manual Sales@laisdcc.com www.laisdcc.com 2002-2018 ©LaisDccTM 1 / 17 1. Decoders CV list, please download it via our website www.laisdcc.com/cvlist.pdf 2. Reset We offer two CV for reset. You can use any of them. A. Write 4 to CV8 to reset the decoders. B. Write 4 to CV30 to reset the decoders. Note: Please refer to the CV list for the default value and the value after reset. Attention: If you find after you reset your decoders keep all the settings the same as before. If so maybe you have lock the decoders. Please program the CV15 to 0 and program CV16 to 1 at the Programming track to unlock it first. Then Reset it again. Link to post Share on other sites More sharing options...
Allegheny1600 Posted March 22, 2020 Share Posted March 22, 2020 Lais are rip-off decoders (I can't remember who design) from China - cheaply made and absolute carp. Buy once then throw away, having learnt your lesson then buy a quality decoder from Zimo, ESU, Lenz, TCS, Digitrax, Zen (there are others but these are amongst the best). As ever, you pays yer money and takes yer chance - buy carp and endlessly faff about with unsatisfying performance or buy quality that works. Link to post Share on other sites More sharing options...
Guest Half-full Posted March 22, 2020 Share Posted March 22, 2020 (edited) I bought a Lais decoder a year or so ago, 9 quid I think it cost. Installed it in a Hornby J50, worked fine, was able to change address etc and stood up well to almost continuous use at a weekend exhibition. Stored the loco away and when I brought it out of storage to get ready for another expo six months or so later the decoder was dead, couldn't get it to respond to any commands, couldn't get it to reset. Binned it and replaced with a ZImo, which I've now standardised across my fleet, inexpensive, very reliable and I know there is great customer support there if I need it. Edited March 22, 2020 by Half-full Link to post Share on other sites More sharing options...
34theletterbetweenB&D Posted March 22, 2020 Share Posted March 22, 2020 (edited) I have not a few duff decoders collected over the years, of various makes, stripped out of friend's locos which didn't work reliably: which then got a Lenz standard or (latterly) a Zimo MX 600 family decoder, and thereafter worked fine. Now, I didn't bin these duffers. I have several trains that need light switches, and they have proved adequate to that task, in the context of a layout operated most days, so they don't get a chance to lose their memory or otherwise corrupt. So that's an option I would suggest for any regular operators. Edited March 22, 2020 by 34theletterbetweenB&D Link to post Share on other sites More sharing options...
RMweb Gold Phil Bullock Posted March 22, 2020 RMweb Gold Share Posted March 22, 2020 Was playing with a Lais decoder in @Pierre Le Brun 's Smokey Joe yesterday. It would not respond sensibly to any changes in CV3/4/5/6 when trying to control acceleration and top speed so gave up.... Link to post Share on other sites More sharing options...
hucknall byron Posted March 22, 2020 Author Share Posted March 22, 2020 Good advice as always on here. Thanks everyone. Cost of this particular lesson £9. Link to post Share on other sites More sharing options...
hucknall byron Posted March 29, 2020 Author Share Posted March 29, 2020 In the interest of fairness I am thinking that the lais decoder may not have been the cause of the trouble now. I have posted on another Hornby 101 trouble thread and I think I may have found another reason which wont surprise many people on here, 1 Link to post Share on other sites More sharing options...
APT Fan Posted July 12, 2020 Share Posted July 12, 2020 On 29/03/2020 at 14:36, hucknall byron said: In the interest of fairness I am thinking that the lais decoder may not have been the cause of the trouble now. I have posted on another Hornby 101 trouble thread and I think I may have found another reason which wont surprise many people on here, So in conclusion the decoder was not faulty? Link to post Share on other sites More sharing options...
Sir TophamHatt Posted July 12, 2020 Share Posted July 12, 2020 Lais decoders have their uses. Running multiple units where you need a separate function decoder gives lais an excellent value-for-money investment. The Lima 156 I used the lais decoder in wasn't great so used them only in a function capacity after that. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now