atom3624 Posted January 28, 2023 Share Posted January 28, 2023 Not often you read this these days, but fantastic service from Royal Mail. I ordered motor #2 for Splendid - same problem as normal - from DCC Supplies. Excellent support from DCC. Requested 2nd signed for - didn't ring / ask for signature just left, so negative point there, even if it's more convenient for some - but considering I ordered Thursday NIGHT, 2 working days' delivery, day 1 should be FR-SAT, but received today, so may get Splendid running over the weekend, to join Brutus on TPE duties! I've yet to locate a decent 'pinion puller' and often end up destroying motors, so didn't want to risk the route a few posts earlier. It is annoying the brushes are often misaligned 'though. Brutus is on motor #3, when most Bachmann and Hornby models with similar running will be on at most #2. Al. Link to post Share on other sites More sharing options...
atom3624 Posted January 28, 2023 Share Posted January 28, 2023 I gently ran in the new motor for Splendid, both directions, before inserting into Splendid. Now fully inserted, new drive cups as well - purchased just in case I damaged the old ones when replacing the motor - I did one. Same power settings gives the same speeds as Brutus - got to be a good sign! (Both max out at the same speed +/- but never hold there - normally perhaps 60%.) Al. 1 Link to post Share on other sites More sharing options...
RMweb Gold adb968008 Posted January 28, 2023 RMweb Gold Share Posted January 28, 2023 I use two guitar string pullers and leverage the bearing off apart. You could always put the bearing in a vice and tap out the motor (its a 2mm shaft) or Tamiya makes a worm puller thats ok. The only one defeating me so far is Bachmanns. 2 Link to post Share on other sites More sharing options...
atom3624 Posted January 29, 2023 Share Posted January 29, 2023 I used to have a couple of pullers, tried playing with heating and 'gentle, firm shock' treatment as well, but always ended up bending the plate, then just binning the motor - one way or the other! Al. Link to post Share on other sites More sharing options...
RMweb Premium ERIC ALLTORQUE Posted January 29, 2023 RMweb Premium Share Posted January 29, 2023 On 19/01/2023 at 21:57, adb968008 said: Now your safe, youve nothing to lose on the old motor. Why not open the can and take a look inside, ive found several models where motor speed was variable, or stopped was due to the brushes losing contact with the commutator. Tweaking the brushes back in has fixed all mine in the past. note how the brushes arent reaching over the armature shaft hole On 19/01/2023 at 21:57, adb968008 said: Now your safe, youve nothing to lose on the old motor. Why not open the can and take a look inside, ive found several models where motor speed was variable, or stopped was due to the brushes losing contact with the commutator. Tweaking the brushes back in has fixed all mine in the past. note how the brushes arent reaching over the armature shaft hole So where you have pulled the flywheels off,are they not balanced which would make them critical to refit? I take it a new one has them fitted. Link to post Share on other sites More sharing options...
atom3624 Posted January 29, 2023 Share Posted January 29, 2023 Replacement / new motors come with flywheels fitted (both ends) but no cups. Drive cups are a tight push fit, but often difficult to remove. Al. Link to post Share on other sites More sharing options...
RMweb Gold adb968008 Posted January 30, 2023 RMweb Gold Share Posted January 30, 2023 (edited) 20 hours ago, ERIC ALLTORQUE said: So where you have pulled the flywheels off,are they not balanced which would make them critical to refit? I take it a new one has them fitted. The cups are just plastic, they are often the same cups as used on the gear box. i just pull them off with pliers. Theres a place on alibaba that sells 12 cups for £7.50 https://www.aliexpress.com/item/1005002394222645.html?mp=1 2mm shaft so fit most motors. its worth noting on the Hattons 66, the bearings are actually unbalanced.. the shaft on one side of the motor is shorter than the other, as there is a plastic face to the motor. This is in the cradle design, so you have to compensate the bearing refitting to the shaft in resprct to motor cradle, otherwise it will either be too tight, or bending the drive shaft to the gearbox. However it is much easier to adjust / fit as its not over tight. The motor size / shape is a fairly standard sized for oo/ho models and several similar alternatives manufacturers are available. You can find a compatible (but not identical) motor for the 68 at a similar price there too.. Piko, LaisDCC and Mehano do one that would fit ( and Bachmann or Heljan has a size that would fit too). ive not found a cheap source of fly wheels yet, though some motors are sold with, but as size is variable, its easier to re-use the old ones. Edited January 30, 2023 by adb968008 Link to post Share on other sites More sharing options...
John-r Posted February 8, 2023 Share Posted February 8, 2023 Hi all, looking for a bit of advice and help. I recently purchased the AS tpe mk 5 set, fantastic wagons, however now looking to buy a class 68 in tpe livery. My questions are the missing handrails, are they hard to fit as I don't have much modelling skills, also have tried YouTube for a tutorial but cannot see any, sending it back to Dapol is out of the question as I live in Ireland, and are Dapol going to supply the missing handrails or do I buy them myself and hopefully someone over here can fit them. Sorry for the long winded post, but any advice, help of feedback greatly appreciated. Regards John. Link to post Share on other sites More sharing options...
RMweb Premium Ncarter2 Posted February 8, 2023 RMweb Premium Share Posted February 8, 2023 3 hours ago, John-r said: Hi all, looking for a bit of advice and help. I recently purchased the AS tpe mk 5 set, fantastic wagons, however now looking to buy a class 68 in tpe livery. My questions are the missing handrails, are they hard to fit as I don't have much modelling skills, also have tried YouTube for a tutorial but cannot see any, sending it back to Dapol is out of the question as I live in Ireland, and are Dapol going to supply the missing handrails or do I buy them myself and hopefully someone over here can fit them. Sorry for the long winded post, but any advice, help of feedback greatly appreciated. Regards John. Hi John, Dapol did acknowledge the error and offered to correct at no cost, though the window for this has since lapsed. I had a very quick look on their site, couldn’t see them being offered as spares, that said, drop them an email, I’m sure they will get back to you. I could imagine fitment may be fiddly, though I have not done it myself. What I can say is I had to return mine because of the poor fitment first time round. I think the supplied a new shell, the one I sent had a blemish on the windscreen and the replacement doesn’t. HTH Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted February 8, 2023 RMweb Gold Share Posted February 8, 2023 8 minutes ago, Ncarter2 said: Hi John, Dapol did acknowledge the error and offered to correct at no cost, though the window for this has since lapsed. I had a very quick look on their site, couldn’t see them being offered as spares, that said, drop them an email, I’m sure they will get back to you. I could imagine fitment may be fiddly, though I have not done it myself. What I can say is I had to return mine because of the poor fitment first time round. I think the supplied a new shell, the one I sent had a blemish on the windscreen and the replacement doesn’t. HTH I think I got a replacement shell as well - a minor mark on the exhaust "disappeared"... Link to post Share on other sites More sharing options...
John-r Posted February 8, 2023 Share Posted February 8, 2023 27 minutes ago, Ncarter2 said: Hi John, Dapol did acknowledge the error and offered to correct at no cost, though the window for this has since lapsed. I had a very quick look on their site, couldn’t see them being offered as spares, that said, drop them an email, I’m sure they will get back to you. I could imagine fitment may be fiddly, though I have not done it myself. What I can say is I had to return mine because of the poor fitment first time round. I think the supplied a new shell, the one I sent had a blemish on the windscreen and the replacement doesn’t. HTH Hi Ncarter2, Thanks very much for the reply, will email Dapol in the morning to see what my options are, cheers john. Link to post Share on other sites More sharing options...
RMweb Premium Gremlin99 Posted February 8, 2023 RMweb Premium Share Posted February 8, 2023 I emailed Dapol the other day about my 68 not "going". They pointed me in the direction of DCC Supplies as their service point. They *do* have parts on their website. They may be a better option :) 1 Link to post Share on other sites More sharing options...
Krieghoff Posted February 15, 2023 Share Posted February 15, 2023 Just received my Class 68 'Splendid' DCC fitted to go with 'Destroyer'. These will head my Tp5's in TPS livery. Cracking locos and now to DCC sound fitting from Digitrains. 1 Link to post Share on other sites More sharing options...
RMweb Gold adb968008 Posted April 9, 2023 RMweb Gold Share Posted April 9, 2023 Looks like a new livery in town.. (not my image) 13 1 Link to post Share on other sites More sharing options...
RMweb Premium ERIC ALLTORQUE Posted April 10, 2023 RMweb Premium Share Posted April 10, 2023 While at York after YMRS had a few hours in station,Felix has got what looks fresh painted gold buffer heads. 6 Link to post Share on other sites More sharing options...
Krieghoff Posted April 10, 2023 Share Posted April 10, 2023 On 09/04/2023 at 08:07, adb968008 said: Looks like a new livery in town.. (not my image) Decent livery. Wonder of Dapol are already on it !! Link to post Share on other sites More sharing options...
RMweb Gold adb968008 Posted April 10, 2023 RMweb Gold Share Posted April 10, 2023 19 hours ago, ERIC ALLTORQUE said: While at York after YMRS had a few hours in station,Felix has got what looks fresh painted gold buffer heads. Felix.. Secret Agent 031 The Cat with the Golden Buffer… is that a James Bond budget remake set in Scarborough instead of Hong Kong ? 1 1 Link to post Share on other sites More sharing options...
RMweb Premium ERIC ALLTORQUE Posted April 11, 2023 RMweb Premium Share Posted April 11, 2023 2 hours ago, adb968008 said: Felix.. Secret Agent 031 The Cat with the Golden Buffer… is that a James Bond budget remake set in Scarborough instead of Hong Kong ? York had a chocolate factory....... Link to post Share on other sites More sharing options...
RMweb Gold Adam1701D Posted April 11, 2023 RMweb Gold Share Posted April 11, 2023 10 hours ago, Krieghoff said: Decent livery. Wonder of Dapol are already on it !! I hope this will feature in a future batch - I love doing "specials". Link to post Share on other sites More sharing options...
RMweb Premium ERIC ALLTORQUE Posted May 18, 2023 RMweb Premium Share Posted May 18, 2023 https://www.Dapol.co.uk/blogs/news/new-oo-gauge-class-68-models-announced?fbclid=IwAR2l7il0KDfE4Z1Vr-EklmPitJdcDCnCleufULZZSdZb8sI5A-8BYdZArkk 2 2 Link to post Share on other sites More sharing options...
RMweb Gold Roy Langridge Posted May 18, 2023 RMweb Gold Share Posted May 18, 2023 On 09/04/2023 at 08:07, adb968008 said: Looks like a new livery in town.. (not my image) And announced today in the next batch :-) 3 Link to post Share on other sites More sharing options...
RMweb Premium ERIC ALLTORQUE Posted May 18, 2023 RMweb Premium Share Posted May 18, 2023 4 Link to post Share on other sites More sharing options...
Tomathee Posted May 18, 2023 Share Posted May 18, 2023 Is it just the small logo near the window that is different between this and the previous release of Intrepid? Scuse my ignorance Link to post Share on other sites More sharing options...
Krieghoff Posted May 18, 2023 Share Posted May 18, 2023 Please get the front handrails on the cab front correctly on this time if anyone from Dapol is listening. 👍👍 ive ordered two sound versions. The Chiltern and a TPE. 👍👍 3 Link to post Share on other sites More sharing options...
G-BOAF Posted May 18, 2023 Share Posted May 18, 2023 2 hours ago, Tomathee said: Is it just the small logo near the window that is different between this and the previous release of Intrepid? Scuse my ignorance It should also have the current (later) nose handrails - the first release was the loco as-built Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now