RMweb Gold Ruston Posted May 4, 2020 RMweb Gold Share Posted May 4, 2020 On 02/05/2020 at 20:07, Porcy Mane said: See above. Also consider junking the cheap as chips Hornby decoder and replacing it with something more capable. You will not regret it. I intend to have Zimo sound fitted but I'm not even supposed to leave the house, let alone go to the Post Office to send the loco away for fitting, so I put this decoder in just so I could run the loco on the layout. 1 Link to post Share on other sites More sharing options...
Porcy Mane Posted May 4, 2020 Share Posted May 4, 2020 1 hour ago, Ruston said: I intend to have Zimo sound fitted but I'm not even supposed to leave the house, let alone go to the Post Office to send the loco away for fitting, so I put this decoder in just so I could run the loco on the layout. I have a Zimo fitted Peckett lying about somewhere. Lying about , probably in the same place I have a Hornby four wire decoder. If I can find the time (the suns out) I'll rewire the Hornby decoder and stick it in the Peckett to see if I can replicate your rough running. P 1 Link to post Share on other sites More sharing options...
RMweb Gold JIJ Posted May 4, 2020 RMweb Gold Share Posted May 4, 2020 On 31/12/2016 at 16:27, Porcy Mane said: Oh no! What have I done? Dunno if it's any help to anyone. P Hi Porcy, I know this was a while ago, but Ijust picked one of these up, wondering how you got it into it's component pieces? Is there a specific solvent you used? Thanks 1 Link to post Share on other sites More sharing options...
Porcy Mane Posted May 4, 2020 Share Posted May 4, 2020 24 minutes ago, JIJ said: wondering how you got it into it's component pieces? Time, patience and a Swan Morton No 17 blade. If you can, never pull individual components out, access the rear of them and push or punch them out. No idea what adhesive Hornby uses but it appears to be of the cyano type. 1 Link to post Share on other sites More sharing options...
RMweb Gold adb968008 Posted May 4, 2020 RMweb Gold Share Posted May 4, 2020 On 31/12/2016 at 16:27, Porcy Mane said: Oh no! What have I done? Forgotten to remove the door darts and buffers ? ;-) 5 Link to post Share on other sites More sharing options...
Porcy Mane Posted May 4, 2020 Share Posted May 4, 2020 12 minutes ago, adb968008 said: Forgotten to remove the door darts and buffers ? Only three buffers. The door dart now resides on a stationary boiler. 2 Link to post Share on other sites More sharing options...
RMweb Gold Ruston Posted May 13, 2020 RMweb Gold Share Posted May 13, 2020 On 04/05/2020 at 13:04, Porcy Mane said: Time, patience and a Swan Morton No 17 blade. If you can, never pull individual components out, access the rear of them and push or punch them out. No idea what adhesive Hornby uses but it appears to be of the cyano type. I am trying to take one of these things apart. I've had one apart that did so with a bit of wiggling and force but the one I'm trying now is solidly glued together and refuses to come apart. There's no way of punching the chimney out from inside at all. Do you know if there is anything that will dissolve the glue without dissolving the plastic? It's probably too much to ask that it doesn't also take the paint off, too. 1 Link to post Share on other sites More sharing options...
RMweb Premium PhilJ W Posted May 13, 2020 RMweb Premium Share Posted May 13, 2020 Cyano is hydroponic so perhaps soaking in warm/hot water might loosen things up. 1 1 Link to post Share on other sites More sharing options...
Porcy Mane Posted May 13, 2020 Share Posted May 13, 2020 (edited) 29 minutes ago, Ruston said: There's no way of punching the chimney out from inside at all. As PhilJW said. Mine was well secured but came away complete after a lot of wiggling and cracking noises. You could try drilling a hole to punch through in the top of the tank to access the bottom of the chimney, using a 1/16 or 1.5 mm drill. The hole would need to be right next to the extension to the casting that goes right up to the tank top and is used by the chassis/body mount screw. P Edited May 13, 2020 by Porcy Mane 2 Link to post Share on other sites More sharing options...
RMweb Gold Ruston Posted May 13, 2020 RMweb Gold Share Posted May 13, 2020 Thanks. I'll have a go at sticking it in some hot water. Though not so hot I can't put my hands in. 1 Link to post Share on other sites More sharing options...
RMweb Premium PhilJ W Posted May 13, 2020 RMweb Premium Share Posted May 13, 2020 2 hours ago, Ruston said: Thanks. I'll have a go at sticking it in some hot water. Though not so hot I can't put my hands in. That would be about the right heat. But I would advise wearing gloves as well. Link to post Share on other sites More sharing options...
RMweb Gold NHY 581 Posted May 14, 2020 RMweb Gold Share Posted May 14, 2020 I contacted the Hornby spares department to enquire about the availability of replacement pick ups for a Peckett W4 earlier this week. They're fragile and easily snapped.....I know this.. I've since had two replies from Hornby. One indicated that they have yet to be supplied with spares. The other outlined the understandable change in working practices at the spares department during this period. The suggestion made was I recontact them once the current situation is resolved. Now its no big deal but out of interest, is anyone else trying to source replacement pick ups? Peters spares don't list them and when Lendons in Cardiff enquired with Hornby last year, on my behalf, they were told they would be available in January this year. Rob. 1 2 Link to post Share on other sites More sharing options...
RMweb Gold PaulRhB Posted May 14, 2020 RMweb Gold Share Posted May 14, 2020 Could you fashion something from some phosphor bronze wire or strips to repair them? I think I got mine from Eileens and I’ve found it very useful on my HOm for extra pickups. Personally I prefer the wire now as it’s a bit more adaptable in tight spots and even though it will wear faster than the wider strip I figured it’s easy to replace and I haven’t worn any away yet and they’ve done several shows on up to a 34’ run and that’s a bit longer than your little layout gems usually get 2 Link to post Share on other sites More sharing options...
RMweb Gold NHY 581 Posted May 15, 2020 RMweb Gold Share Posted May 15, 2020 (edited) 5 hours ago, PaulRhB said: Could you fashion something from some phosphor bronze wire or strips to repair them? I think I got mine from Eileens and I’ve found it very useful on my HOm for extra pickups. Personally I prefer the wire now as it’s a bit more adaptable in tight spots and even though it will wear faster than the wider strip I figured it’s easy to replace and I haven’t worn any away yet and they’ve done several shows on up to a 34’ run and that’s a bit longer than your little layout gems usually get Thanks Paul. I tried the PB strips but it didn't work. It's so tight in there that there wasn't enough flex in the strip to allow the movement it all needs to maintain contact and provide just the right amount of movement. Key to these little chaps is setting the front pick ups just right. If the front pick ups aren't set right the crank pins on the front wheels will interfere with the cross heads and that will give a tight spot. It's got to be evenly set on both wheels. The spare is listed by Hornby but it appears to have never been produced/provided in the three years ( just over) the locos have been available. Rob. Edited May 15, 2020 by NHY 581 1 3 Link to post Share on other sites More sharing options...
RMweb Gold Ruston Posted May 15, 2020 RMweb Gold Share Posted May 15, 2020 On 13/05/2020 at 18:30, Ruston said: Thanks. I'll have a go at sticking it in some hot water. Though not so hot I can't put my hands in. That didn't work. Nothing will budge on it at all. 1 3 Link to post Share on other sites More sharing options...
Caledonian Posted May 16, 2020 Share Posted May 16, 2020 But yet when you don't want bits dropping off... Link to post Share on other sites More sharing options...
Porcy Mane Posted May 16, 2020 Share Posted May 16, 2020 33 minutes ago, Caledonian said: But yet when you don't want bits dropping off... As you get older you get used to it! 2 3 Link to post Share on other sites More sharing options...
RMweb Gold Ruston Posted May 16, 2020 RMweb Gold Share Posted May 16, 2020 I did get it apart, eventually. Brute force and ignorance, mostly. 5 2 Link to post Share on other sites More sharing options...
Paul.Uni Posted July 18, 2020 Share Posted July 18, 2020 Release dates on the Hornby website: R3640 'Niclausse' Autumn 2020 R3825 Peckett grey Autumn 2020 R3702 'Daphne' Winter 2020-2021 R3703 'Bear' Winter 2020-2021 R3868 Crawshay Brothers green Spring 2021 R3869 'Lady Cornelia' Spring 2021 R3761 'Lady Edith' is still listed as Winter 2019-2020 1 1 Link to post Share on other sites More sharing options...
neilkirby Posted July 19, 2020 Share Posted July 19, 2020 22 hours ago, Paul.Uni said: Release dates on the Hornby website: R3761 'Lady Edith' is still listed as Winter 2019-2020 So was Daphne until last week!? Neil 1 Link to post Share on other sites More sharing options...
johnd Posted July 19, 2020 Share Posted July 19, 2020 20 minutes ago, neilkirby said: So was Daphne until last week!? Neil So was Bear ! 1 Link to post Share on other sites More sharing options...
Paul.Uni Posted August 22, 2020 Share Posted August 22, 2020 1 Link to post Share on other sites More sharing options...
Paul.Uni Posted October 18, 2020 Share Posted October 18, 2020 (edited) On 18/07/2020 at 17:35, Paul.Uni said: Release dates on the Hornby website: R3640 'Niclausse' Autumn 2020 R3825 Peckett grey Autumn 2020 R3702 'Daphne' Winter 2020-2021 R3703 'Bear' Winter 2020-2021 R3868 Crawshay Brothers green Spring 2021 R3869 'Lady Cornelia' Spring 2021 R3761 'Lady Edith' is still listed as Winter 2019-2020 R3761 'Lady Edith' now has a release date of Summer 2021. All release dates for the other Pecketts remain the same. Edited October 18, 2020 by Paul.Uni 1 Link to post Share on other sites More sharing options...
RMweb Gold The Johnster Posted October 21, 2020 RMweb Gold Share Posted October 21, 2020 (edited) I've filled the coal bunker on mine, with coal. I bet not many other people have bothered with this! I've also provided Modelu industrial lamps fore and aft, but no crew as yet. Haulage is increasing over time and use, presumably due to tyre surfaces roughing up; she will now pull a 10 wagon loaded coal train with foam or card filliers and a top layer of coal. What a constant delight owning this lovely little loco is! Edited October 21, 2020 by The Johnster 4 Link to post Share on other sites More sharing options...
RMweb Gold Edwardian Posted October 22, 2020 RMweb Gold Share Posted October 22, 2020 On 22/08/2020 at 19:16, Paul.Uni said: Well, I was, until my supplier's allocation was yanked. 2 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now