Jump to content
 

Heljan Class 35 Hymek


tarifa
 Share

Recommended Posts

  • RMweb Gold

With a great deal of warranted attention recently given to the Warships, I am however of the opinion the Hymek is still one of the "best" models around.  I did a little updating to bring it into line with the current level of detailing on my own models.

A roof grill and etched fan is fitted and is renumbered to 7017 with EE etches.  The air tanks have been fitted in the correct location and full buffer beam detail with wire draw bars in loo of the tension lock couplings.  A chequer plate foot shelf is added above the buffer beam with the foot iron added.  Sound is fitted with the speaker located in the fuel tanks.  A thumb print is attached attempting to show the work.  I'm sure other chaps have done similar work so any photos.

 

post-1644-0-90029000-1441635946_thumb.jpg

 

post-1644-0-25287900-1441635951_thumb.jpg

 

Mike

Edited by tarifa
  • Like 19
Link to post
Share on other sites

  • 2 years later...
  • RMweb Premium

With a great deal of warranted attention recently given to the Warships, I am however of the opinion the Hymek is still one of the "best" models around.  I did a little updating to bring it into line with the current level of detailing on my own models.

A roof grill and etched fan is fitted and is renumbered to 7017 with EE etches.  The air tanks have been fitted in the correct location and full buffer beam detail with wire draw bars in loo of the tension lock couplings.  A chequer plate foot shelf is added above the buffer beam with the foot iron added.  Sound is fitted with the speaker located in the fuel tanks.  A thumb print is attached attempting to show the work.  I'm sure other chaps have done similar work so any photos.

 

attachicon.gifFront End Heljan 7017.jpg

 

attachicon.gifHeljan Hymek Detailed and renumbered 7017.jpg

 

Mike

 

Great Job !

 

I recently got rid of what I considered to be the poor lighting system and fitted lighting units made by Jason Edmunds (Stickswipe) of ebay fame .

This allowed much better headcode lighting and individual control of the red tail lights .

 

The Legomanbiffo sound was improved beyond all recognition by fitting an EM1 under the etched fan grille and a

putting a sugar cube into the tanks .

That speaker combo didn't work anywhere near as well with the Zimo Hymek project , still working on that one !

 

Albie  

Link to post
Share on other sites

  • RMweb Premium

Great Job !

 

I recently got rid of what I considered to be the poor lighting system and fitted lighting units made by Jason Edmunds (Stickswipe) of ebay fame .

This allowed much better headcode lighting and individual control of the red tail lights .

 

The Legomanbiffo sound was improved beyond all recognition by fitting an EM1 under the etched fan grille and a

putting a sugar cube into the tanks .

That speaker combo didn't work anywhere near as well with the Zimo Hymek project , still working on that one !

 

Albie

Albie, did you have to hack the chassis block to fit the EM1? Been a while since iv been in a Heljan hymek and mines dying for a sound unit

Cheers

James

Link to post
Share on other sites

  • 1 year later...
  • RMweb Gold

We love these locos . always a favorite and Abbotswood allocation needs a couple of Lickey bankers to appear - either running light down to Gloucester or assisting a southbound train following a loco failure in the Bromsgrove area. So D7022/3 currently in works....

 

As per @tarifa's original post - etched fan grille and relocated air tank - plus those horns are a bit spindly, we replace with Markits turned brass jobbies - https://www.ebay.co.uk/i/324072729006?chn=ps&norover=1&mkevt=1&mkrid=710-134428-41853-0&mkcid=2&itemid=324072729006&targetid=879157198036&device=c&mktype=pla&googleloc=9045574&poi=&campaignid=9437867024&mkgroupid=104303480548&rlsatarget=aud-629407027425:pla-879157198036&abcId=1140486&merchantid=7262894&gclid=Cj0KCQjwsYb0BRCOARIsAHbLPhGB_ngsSc1d8wBjVceotPiEgF8Zok9R2vDmdSgk19HgUsnjZKLPZI8aAun-EALw_wcB

 

Etched numbers too from Shawplan, and headboard clips removed from early locos but for locos in later life theres one thing missing from the Heljan model - the retro-fitted lower drivers door grab handles. See below - another excellent Brush Veteran photo

 

7001 Reading March 72 Slide 226

 

So have tried several ways to emulate this - heres latest attempt which I reckon is as good as I can get it, 2mm square hollow brass with a thin strip from a grille etching soldered on prior to installation....

 

 

 

 

 

57D6E275-5384-4115-99D1-AC493F21E7A1.jpeg

Edited by Phil Bullock
  • Like 10
  • Craftsmanship/clever 2
Link to post
Share on other sites

  • 3 months later...

Wonder if anyone could help.  Had a 35 for a good while and is a smooth runner on DC.  Want to chip it but no point until can get the ussue resolved.

 

It hasn't ran in loads but has been up n down shunting type planks.

 

It's started to be a little hesitant at slow to get moving as if it's sapping evergy then it'll surge forward slightly making smooth starts not impossible but awkward.

 

If running fast for about 15 seconds it slows down then stops, presumably to cool down due to overheating or partial short maybe  Unsure.

 

Any ideas what the issue is or how to resolve it?

 

Getting the circuit board out to have a closer look seems it might be tricky and not sure how to do it if need be.

 

The loco is useless until can get it to stop dying somehow. 

 

Ugh. 

 

?

 

 

 

Edited by Knuckles
Link to post
Share on other sites

Tried it with an older R965 Hornby controller (ones with a stepped down section for the actual controls) and a Gaugemaster Combi.  Same affect.  I know the controller you mentioned has a crappy safety cut out 'feature.'

 

Pick ups are perfectly touching and not dirty.

 

Can't get into the motor to maybe oil the spindles as the instructions are lacking information and currently unsure how to disassemble it without busting it.

Edited by Knuckles
Link to post
Share on other sites

Have you got the parts diagram? Should help you recognise the parts.  Heljan use a pretty uniform construction plan for their fully body width models, so despite never having had the body off a 35 would expect to find a cast 'U' section chassis, with the motor retained by a pair of rubber cushions holding the motor captive inside the 'U'. You just ease it all apart.

 

I feel you are right to try applying lubrication to the motor bearings: a little dot of light oil on each to see if that fixes it, as it does sound like dry bearings, which heat and  seize

Link to post
Share on other sites

On 07/09/2015 at 16:31, tarifa said:

With a great deal of warranted attention recently given to the Warships, I am however of the opinion the Hymek is still one of the "best" models around.  I did a little updating to bring it into line with the current level of detailing on my own models.

A roof grill and etched fan is fitted and is renumbered to 7017 with EE etches.  The air tanks have been fitted in the correct location and full buffer beam detail with wire draw bars in loo of the tension lock couplings.  A chequer plate foot shelf is added above the buffer beam with the foot iron added.  Sound is fitted with the speaker located in the fuel tanks.  A thumb print is attached attempting to show the work.  I'm sure other chaps have done similar work so any photos.

 

Not my era, or area. But the Hymek was one of my favourite engines on my railway as a boy. So I cuffed rule#1 about its ear and ordered one from KMRC.

 

But I'm interested in the updates that you made. Do you have any further details/links to the etches and placement of the air tanks, Mike?

Link to post
Share on other sites

  • RMweb Gold
22 minutes ago, D1051 said:

My recent experience , it might not be the motor .But cup attached to the worm drive on top of the bogie. Mine had split & ran exactly as you describe.

I'm old school & not into DCC.

 

I stripped 6 Heljan locos as a precaution & the said cup was split on all.

 

After a while the cup becomes loose due to split.

 

To me its a poor design . 


Agreed .... but a very carefully applied touch of superglue will retain cup on shaft and eliminate drive slip ....

Link to post
Share on other sites

  • RMweb Gold
7 minutes ago, truffy said:

But I'm interested in the updates that you made. Do you have any further details/links to the etches and placement of the air tanks, Mike?

 

The roof grill and fan is from A1 models many years ago.  The front buffer beam top step is brass chequer plate and the step iron is brass strip.  The running numbers are extreme etchings.  To locate the air tanks I took photos of 7017 down on the WSR.   If you think it will help I could take some photos for you.

 

Mike

  • Thanks 1
Link to post
Share on other sites

That would be fantastic if it’s not too much trouble!

4 minutes ago, tarifa said:

To locate the air tanks I took photos of 7017 down on the WSR.   If you think it will help I could take some photos for you.

 

Link to post
Share on other sites

8 hours ago, D1051 said:

My recent experience , it might not be the motor .But cup attached to the worm drive on top of the bogie. Mine had split & ran exactly as you describe.

I'm old school & not into DCC.

 

I stripped 6 Heljan locos as a precaution & the said cup was split on all.

 

After a while the cup becomes loose due to split... 

As a relative newbie to operating Heljan product (first suitable model for me was the BTH type 1/Class 15) what sort of time are we talking before this problem becomes evident? Haven't encountered this one - so far...

Link to post
Share on other sites

Any know how to remove the wheels? I pushed mine out a bitt too far on checking the back-to-backs and can't now press then in a bit without removing the wheel sets!

 

How does the original Tri-ang Hymek compare to the Heljan model?

 

Link to post
Share on other sites

  • RMweb Gold
2 hours ago, roythebus said:

Any know how to remove the wheels? I pushed mine out a bitt too far on checking the back-to-backs and can't now press then in a bit without removing the wheel sets!

 

How does the original Tri-ang Hymek compare to the Heljan model?

 

Badly.

 

The Heljan Hymek is vastly superior both in haulage capacity and accuracy. It is one of Heljan's better models. It has the correctly offset roof grill and in general is a vastly superior model.

  • Like 1
  • Agree 1
Link to post
Share on other sites

21 hours ago, tarifa said:

The roof grill and fan is from A1 models many years ago.

 

Word to the wise: don't try googling "A1 models"! :blink:

 

OTOH, Shawplan do a fan and grille set for the Class 35 (DP35-00)

  • Like 1
Link to post
Share on other sites

  • 3 weeks later...
  • RMweb Gold
On 13/07/2020 at 19:49, roythebus said:

Any know how to remove the wheels? I pushed mine out a bitt too far on checking the back-to-backs and can't now press then in a bit without removing the wheel sets!

 

How does the original Tri-ang Hymek compare to the Heljan model?

 


 

Hornbys Hymek wasnt bad in its day. The body shape is ok, however the paint job let most of them down (limitations of the day, I should add). If you put the effort in, repainted, flush glazed, your left with a decent body.

Trouble is the Triang chassis was poor by modern standards, the Hornby one is ok but Heljans is way ahead better.

 

it is testament to the model that some can fetch £60 on ebay, though older ones can be had for c£20.

  • Agree 1
Link to post
Share on other sites

I have posted this photo elsewhere, but it may be relevant here. It shows two Heljan Hymeks (one detailed with mesh roof grille) and a detailed Triang version with two motor bogies of the original cast metal type (i.e. pre-ringfield). As an experiment I chose to finish the Triang one in a might-have-been maroon livery. The Triang cabs are fractionally too short, which shows in the slightly too-narrow side windows, but overall it really isn't a bad model, but definitely lacks the more refined running of the Heljan mechanisms (as adb968008 says above).

38107012425_942022e873_c.jpg
Hymeks in Triplicate - 2 by Jeffrey Lynn, on Flickr

Edited by SRman
  • Like 2
Link to post
Share on other sites

  • RMweb Gold
2 hours ago, SRman said:

I have posted this photo elsewhere, but it may be relevant here. It shows two Heljan Hymeks (one detailed with mesh roof grille) and a detailed Triang version with two motor bogies of the original cast metal type (i.e. pre-ringfield). As an experiment I chose to finish the Triang one in a might-have-been maroon livery. The Triang cabs are fractionally too short, which shows in the slightly too-narrow side windows, but overall it really isn't a bad model, but definitely lacks the more refined running of the Heljan mechanisms (as adb968008 says above).

38107012425_942022e873_c.jpg
Hymeks in Triplicate - 2 by Jeffrey Lynn, on Flickr

Wow..Your picture is haunted


There seems to be a ghostly apparition of an EMU ?

  • Funny 1
Link to post
Share on other sites

10 hours ago, adb968008 said:

Wow..Your picture is haunted


There seems to be a ghostly apparition of an EMU ?

 

I don't see any EMUs there! Must be a figment of your imagination. :jester:

 

Actually, a resin Bulleid style2 HAP unit I was working on at the time. It has progressed further since that photo was taken.

  • Craftsmanship/clever 1
Link to post
Share on other sites

  • 3 weeks later...

Anyone found a source of replacement airhorns for the Heljan Hymek? I just got mine out and one of them has gone missing. Tried Gaugemaster but they don't seem to have them.

 

PS. I have an unbuilt Triang Hornby CKD Hymek exactly like the one I had as a kid. Tempting to build it but I'm sure it's worth more unbuilt....

Edited by Salmotrutta
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...