A sound decision – Bachmann 32-480DS on analogue DC
There was mention on RMweb this week of the Class Forty Preservation Society (CFPS) which in turn reminded me that Bachmann had produced a Digital Sound model of D211 ‘Mauritania’. A Google search returned a model priced at not a lot more than the current price of the non sound fitted Class 40s. I succumbed.
D211 ‘Mauritania’
For use with my analogue DC controllers it was my intention to replace the digital sound chip with a blanking plate. However on reading the Bachmann instructions for the Class 40 (almost a first for me) I noted that the default settings showed that sound was enabled for analogue DC. I would investigate.
Here is what the ESU data sheet has to say about the Lok 4 decoder fitted to the Class 40:
I use Gaugemaster DS controllers and run them entirely with the ‘simulator’ switched on. For those of you unfamiliar with the Gaugemaster DS, the ‘simulator’ introduces a delay between turning the control knob and the engine responding. This is also referred to as ‘inertia’ control. Use of the simulator also cuts the maximum power (voltage) applied to the engine. I mention this because on my first attempt to run D211 I had the simulator switched on and nothing happened (I thought another duff model). I repeated the exercise and noticed that the lights had come on, but no movement. I would have one more attempt at running the model with the sound chip inside. The lights came on, I waited a bit longer and to my amazement the ‘engine‘ fired up and after a rather lengthy delay the locomotive slowly moved off. I then had an epiphany - if I switched off the ‘simulator’ would it all happen more quickly? Yes it did – we were in business.
When you look around there are plenty of references to running digital sound locomotives on analogue DC. Briefly the chip needs power so nothing can happen until the control knob is switched on. Equally important – at the end of a running session you don’t immediately switch the control knob right off because that would kill all the power to the chip and there would be no further sound. Instead you have to slowly decrease the power, a few increments at a time, and this enables the chip to close the engine down and broadcast a sequence of engine shutdown sounds. Only when all the sounds have died down and the lights have shut off should the control knob be fully turned off.
Stopping:
Shut Down:
Sounds and the power supplied to the locomotive motor are loaded in sequence within the chip and are output according to the power input from the DC controlled supply. There is one set of instructions for increasing power and another for decreasing power. For DC operation other people have suggested 2 volts to bring the lights on, 6 volts to start the engine and 8 volts to move off. My understanding of the Gaugmaster Controllers is that the voltage is kept constant (around 14 volts DC) and power output is varied by altering the frequency and lengths of pulses. My observations suggest ‘starting’ and ‘shut down’ require a control knob setting between five and six, whilst running needs a value around eight. A little above eight and the locomotive can emit a strong engine noise, drop the knob below eight and the engine coasts. ‘Stopping’ seems to be activated at settings between six and seven.
Running:
Bachmann provide ‘Hints for using the model’ – (I am guessing for digital operation):
It also becomes apparent that the speed of the locomotive is dictated by the embedded settings within the chip. The position of the control knob should be viewed as a setting for a particular running condition rather than as a variable speed control. For each setting the chip contains a target speed together with incremental steps to reach that speed. The result is a smooth increase (or decrease) in speed between control knob settings in much the same way that the Gaugemaster simulator gradually ramps the speed up or down in response to changes in control knob position.
I am amazed at how much play value there is in ‘driving’ the digital sound locomotive. I am still on a learning curve but the following compilation video hints at what is possible. I was holding the camera with one hand and moving the control knob with the other – well, that is my excuse for the rather bouncy pictures.
Compilation:
Will I purchase another Digital Sound locomotive? Possibly (bank manager / wife permitting). Running on analogue DC comes literally without a lot of the bells and whistles although you can hear the screech of brakes. Even without all the detail the engine noise is full of nostalgia. Would I want all my engines sound enabled? No. It is surprising how much noise is emitted by one engine. The volume completely drowns out the clickety click sound from the carriages. I would say that after a short session with sound, running a non-sound locomotive comes as a bit of a relief. (With full digital control there is the capability of reducing sound levels – that might be a bonus.)
Am I going to change to DCC operation? No. Coincidently my last Blog Post showed the complexity of the current wiring beneath my analogue DC layout. As others have observed, DCC operation could require much more with some people recommending connections to every length of rail and separate microswitches for all the points. I cannot see that happening here! If I can run the odd Digital Sound locomotive – why should I change?
From above Bachamann D211 ‘Mauritania’ ( R ) with D210 ‘Empress of Britain’ ( L )
What about the appearance of D211? There are number of views below comparing the earlier 2007 Bachmann model of D210 ‘Empress of Britain’ with ‘Mauritania’. From a distance there seems little to choose between D210 and D211.
Side on Bachamann D211 ‘Mauritania’ ( R ) with D210 ‘Empress of Britain’ ( L )
However on closer inspection there are subtle changes to the body shape and some more obvious changes to handrails and lamp irons which I believe had been added erroneously by Bachmann to the early model.
Front on Bachamann D211 ‘Mauritania’ ( R ) with D210 ‘Empress of Britain’ ( L )
Rubbing noses Bachmann D211 ‘Mauritania’ ( R ) with D210 ‘Empress of Britain’ ( L )
Spot some differences to the under frame, Bachmann D211 ‘Mauritania’ ( R ) with D210 ‘Empress of Britain’ ( L )
This Blog post is about Bachmann 32-480DS. It was bought new and the default settings for the chip include running on analogue DC. My understanding is that both the ESU Lok 3.5 and 4.0 chips will produce sound on analogue DC. However not all Bachmann locomotives are shipped with chips set at their default settings. Straight out of the box some Bachmann models will not produce sound on DC analogue and may not even run with the digital chip in place. I am guessing that for these models the access to a digital system is needed to reset the chip to the default values. I have no knowledge or experience of Hornby TTS locomotives so may have to stand corrected but from comments on the ‘web’ these models cannot produce sound on analogue DC.
Well it is 01 May this weekend and we are still getting snow. It is definitely not gardening weather so time to go and play!
- 2
12 Comments
Recommended Comments
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now